who designed byd seal

The eight core components of an automobile cooling system include the water pump, radiator, cooling fan, thermostat, expansion tank (compensation tank), water temperature sensor, and the water jackets in the engine block and cylinder head. As the system's core, the water pump drives coolant circulation to ensure uniform heat transfer; the radiator dissipates coolant heat into the air through thermal exchange; the cooling fan enhances heat dissipation efficiency by forcing airflow during high-temperature conditions; the thermostat automatically switches between large and small circulation loops based on temperature to optimize engine warm-up and temperature regulation; the expansion tank stores and regulates coolant volume to maintain system pressure balance; the water temperature sensor provides real-time temperature monitoring and feedback to the control unit; the engine water jackets directly contact high-temperature components for heat transfer. Additionally, the system incorporates auxiliary components (such as hoses and protective plates) to enhance stability. Its operational principle relies on coolant circulation and thermal exchange, maintaining engine operation within the optimal 80-120℃ range while supplying heat for the vehicle's heating system. Coolant requires periodic inspection and replacement to prevent compromised cooling performance due to degradation or leaks.

The cooling system of an automobile engine is commonly referred to as the "engine cooling system", which is mainly divided into two types: water cooling and air cooling. Among them, the water cooling system is the most widely adopted design at present. The water cooling system uses a water pump to drive the coolant to circulate inside the engine. After absorbing heat from high-temperature components such as the cylinder block and cylinder head, the coolant flows through the radiator to dissipate heat into the air, and then returns to the engine to continue circulating. This system consists of core components including a water pump, radiator, thermostat, cooling fan, and expansion tank. The thermostat automatically adjusts the coolant circulation path according to the engine temperature to ensure the engine warms up quickly and maintains an optimal operating temperature of 80-90°C. The coolant is usually a mixture of water, antifreeze, and corrosion-inhibiting additives, which can effectively prevent scaling and corrosion. Modern cooling systems also have dual functions: they can not only dissipate heat for the engine but also provide heating for the vehicle cabin through the heater core. Compared with the air cooling system, which has been basically phased out, the water cooling system has advantages such as uniform cooling, low noise, and high reliability. It is a key system to ensure the stable performance of the engine and extend its service life.

The car cooling system is a key mechanism ensuring the engine's stable operation. Its core function is to transfer the heat generated by the engine to the outside air through circulating coolant, preventing overheating damage. The system mainly consists of components such as the radiator, water pump, thermostat, cooling fan, and pipelines that work together. The radiator exchanges heat with air through large-area heat-dissipating fins; the water pump drives the circulation of coolant; and the thermostat automatically switches between large and small circulation modes according to the coolant temperature—closing the large circulation at low temperatures to quickly warm up the engine, and opening it at high temperatures to enhance heat dissipation. Coolant is typically an ethylene glycol-based mixture, serving functions such as freeze protection, corrosion inhibition, and lubrication of internal components. Regular maintenance, including checking the fluid level, replacing the coolant (recommended every 2 years or 40,000 kilometers), and removing debris from the radiator, can significantly improve the system's efficiency. Neglecting maintenance may lead to serious failures such as engine overheating and cylinder block deformation, with repair costs potentially reaching thousands of ringgit. Additionally, some models utilize electronic water pumps and intelligent temperature control technology to further optimize the balance between energy consumption and heat dissipation.

The limitations of in-vehicle navigation mainly manifest in three aspects: software, hardware, and environment. At the software level, outdated system versions or failure to update promptly can result in obsolete map data that fails to reflect newly constructed roads or changes in traffic regulations, particularly in remote areas where update cycles may extend for months. Hardware issues include navigation module malfunctions, poor antenna signal reception, or screen damage, all of which directly impair functionality. Environmental factors such as high-rise urban areas, tunnels, or severe weather conditions may disrupt satellite signals, causing positioning drift or signal loss. Additionally, navigation algorithms suffer from inflexible logic, rendering them incapable of dynamically adapting to real-time traffic changes like rush-hour congestion or temporary road closures. It is advisable to manually update map data periodically, utilize mobile hotspots for auxiliary positioning in signal-blind zones, and manually adjust routes based on driving experience. While some premium vehicle models support real-time online updates, owners must still proactively maintain the system. Notably, unstable power connections or vehicle electronic system failures may also indirectly lead to navigation anomalies, necessitating regular circuit inspections.

Automotive navigation systems operate by receiving signals from global satellite positioning systems such as the United States' GPS, China's BeiDou, Russia's GLONASS, or Europe's Galileo. These satellites transmit signals containing position and time information. Navigation devices calculate distances by measuring the signal propagation time from satellites to receivers and combining it with the speed of light, then use signals from at least three satellites for triangulation to determine the vehicle's latitude, longitude, and altitude. The navigation host matches the obtained position coordinates with built-in electronic map data to display the vehicle's real-time location on the screen. Meanwhile, it further improves positioning accuracy by integrating data from on-board sensors like speed sensors and gyroscopes. The system plans optimal routes based on the destination, real-time traffic conditions (such as congestion or restrictions), and driving preferences (shortest distance or fastest time), and guides drivers through voice and visual prompts. Modern navigation systems also integrate real-time traffic updates, point-of-interest queries, and multimedia entertainment functions. Some high-end models even support multi-mode fusion navigation technology, combining inertial navigation or geomagnetic navigation to enhance positioning reliability in complex environments. With technological advancements, navigation systems are deeply integrating with vehicle networking and autonomous driving technologies, and will provide higher-precision lane-level navigation services in the future.